The TRC ALUMINUM SHIELD ROOF SYSTEM Beautifies, water proofs, stops rust and corrosion, reduces roof movement, is easy to apply and reflects 80% of UV rays.

ALUMINUM SHIELD METAL ROOF SYSTEM

WHAT IS THE ALUMINUM SHIELD METAL ROOF SYSTEM?

The ALUMINUM SHIELD ROOF SYSTEM is a waterproofing and rust preventative coating system specifically designed for the special needs of aluminum roofs. Using TRC roofing materials, The ALUMINUM SHIELD SYSTEM is not a simple coating. Instead, it's a combination of three easy-to-use products that form an aluminum shield over metal roofs to water proof, prevent rust and corrosion, insulate, beautify and protect. And it does its job so well that it's guaranteed.

WATERPROOFS

The ALUMINUM SHIELD ROOF SYSTEM is specifically designed to waterproof metal roofs. This is accomplished by using ALUMINUM QUICK PATCH on applicable seams and fastener heads where needed to seal leaking or potential leaking areas. Texas Refinery's ALUMINUM QUICK PATCH is fast and easy to apply because it is self adhering. Just peel the backing off and stick it in place. It's flexible and gives long-lasting waterproofing protection.

STOPS RUST AND CORROSION

The first step in the ALUMINUM SHIELD ROOF SYSTEM is a coating of Texas Refinery's ANTI-OXIDENE COATING. This stops rust and corrosion immediately. Rust and corrosion are the biggest enemies of a metal roof. Eventually all metal roofs will rust and corrode and if left untreated, they will completely deteriorate the roof. If rust and corrosion have not yet begun to form, the ALUMINUM SHIELD SYSTEM prevents them from starting thus reducing costly roof repairs. But, even if rust and corrosion have already started, TRC roofing materials stop these destructive forces from doing further damage.

The ALUMINUM SHIELD METAL ROOF SYSTEM provides a gleaming, protective coat of aluminum over the entire roof surface. This reflects up to 80% of the sun's ultra violet rays away from the roof surface. Unlike most insulating materials which retard heat after it has penetrated the roof, the ALUMINUM SHIELD SYSTEM stops heat before it even enters the roof system. This means cooled interiors and less air-conditioning costs and fewer roof repairs.

EASY TO APPLY

The ALUMINUM METAL SHIELD ROOF SYSTEM with TRC roofing materials is fast and easy to apply! In fact, it's so easy that it is ideal for do-it-yourself applications. No expensive labor is required. First, QUICK DRY ANTI-OXIDENE COATING is applied. Next, ALUMINUM QUICK PATCH is applied to seams and fastener heads where needed to seal leaking or potential leaking areas. And then, ALUMINUM COATING is applied to the entire roof. It's that fast, easy, effective and economical.

REDUCES ROOF MOVEMENT

With the ALUMINUM SHIELD METAL ROOF SYSTEM, roof surfaces are kept at the same realitive temperature. This helps eliminate thermal shock which causes expansion and contraction of metal roofs. This lack of movement means longer life for metal roofs.

BEAUTIFIES

Even older, rusted metal roofs are restored to like-new brilliance with TRC roofing materials Pure aluminum flakes give a long lasting bright finish that enhances property values.

Aluminum Roof Coatings and Patching Products

Click on Product Name for Details?

ALUMINUM SHIELD METAL ROOF SYSTEM Application instructions

1. Roof surface must be prepared properly. The surface must be clean, sound and free from all dirt, dust, loose rust or other loose particles. Wire brush rusted areas.

Application should not be made on damaged metal where rusted-through areas are apparent and the metal is too thin for self-support. If these conditions exist, replace metal roof sections as necessary and proceed with application.

Make sure all screws and fasteners are in place and secure. Loose fasteners or screws must be retightened. Fasteners or screws that are damaged or missing must be replaced.

2. After the surface has been properly prepared, apply QUICK-DRY ANTI-OXIDENE to the entire foof surface. QUICK-DRY ANTI-OXIDENE is easily applied by roller, brush or spray. On flat surfacs, the coverage rate is 300 square feet per gallon. On corrugated metal, one gallon cover approximately 200 square feeet. Allow QUIC-DRY ANTI-OXIDENE to dry for approximately four hours under favorable drying conditions before proceeding with the next application procedure.

3. Next, apply 3-inch wide ALUMINUM QUICK-PATCH to applicable seams and fastener heads where needed to seal leaking or potential leaking areas. Obviously, for best and most long-lasting results ALUMINUM QUICK-PATCH should be applied to all vertical seams, horizontal seams and fastener heads.

When appplying ALUMINUM QUICK-PATCH , start at the low point of the application, align roll, peel back 12 inches of release paper and press exposed portion into place directly over seam and/or fasteners. Carefully unroll the ALUMINUM QUICK-PATCH, removing paper and pressing material into place as you go.

Alternately, when applying ALUMINUM QUICK-PATCH over fastener heads, the ALUMINUM QUICK-PATCH can be cut into 3-inch x 3-inch squares. These squares should be cut with the release paper still attached. Then, after removing the release paper from each square, the 3" x 3" squares should be affixed directly over each fastener head.

4. Apply ALUMINUM COATING over entire roof surface by roller, brush or spray.

When Texas Refinery Corp. ALUMINUM ROOF COATING is applied, the rate of coverage is one gallon per 300 square feet on flat roofs. The rate of coverage is one gallon per 200 square feet on corrugated metal. When ALUMINUM ROOF COATING is applied, a five-year warranty applies.

When Texas Refinery Corp. TEXOTROPIC FIBERED ALUMINUM ROOF COATING is applied, the rate of coverage is one gallon to 100 square feet on flat roofs. The rate of coverage is one and one-half gallon per 100 square feet on corrugated metal. When TEXOTROPIC FIBERED ALUMINUM ROOF COATING is applied, a 6 year warranty applies.

.